Presse universelle MecaMotion par 
PROFINET error list
Press errors are given to the PLC via the PROFINET link.
As explained in the chapter "Overview of the PROFINET dialogue", these errors are given by the 5 bytes located at addresses 245... 249.
Each byte is composed of 8 bits and each bit corresponds to a specific error => 40 errors maximum.
List of possible errors:
Error number |
Type |
Description erreur |
Direction (from the press) |
Address |
Format |
|---|---|---|---|---|---|
1 |
Error |
Internal error, contact Softeca |
OUT |
246.0 |
BIT |
2 |
Error |
The program number to be activated doesn't exist |
OUT |
246.1 |
BIT |
3 |
Error |
Force overload with range 1 (small range) |
OUT |
246.2 |
BIT |
4 |
Error |
Force overload with range 2 (large range) |
OUT |
246.3 |
BIT |
5 |
Error |
Emergency stop detected |
OUT |
246.4 |
BIT |
6 |
Error |
Axis in technological error |
OUT |
246.5 |
BIT |
7 |
Error |
External encoder error (measuring sensor) |
OUT |
246.6 |
BIT |
8 |
Error |
Program execution timeout (Time set in the MecaMotion parameters, the function is disabled if the parameter is at 0) |
OUT |
246.7 |
BIT |
9 |
Error |
Force limits of a positioning exceeds maximal force on selected range |
OUT |
247.0 |
BIT |
10 |
Error |
Force limit exceeded in a positioning |
OUT |
247.1 |
BIT |
11 |
Error |
Telegram too large (part program sent by Ethernet (Mecamotion)) |
OUT |
247.2 |
BIT |
12 |
Error |
"Force Measurement" instruction without "Curve Recording" instruction before |
OUT |
247.3 |
BIT |
13 |
Error |
Incorrect Firmware License |
OUT |
247.4 |
BIT |
14 |
Warning |
Curve recording: Too many points (Velocity too low?) |
OUT |
247.5 |
BIT |
15 |
Error |
Division by 0 |
OUT |
247.6 |
BIT |
16 |
Error |
Arithmetic overflow of an integer |
OUT |
247.7 |
BIT |
17 |
Error |
Positive software limit switch reached |
OUT |
248.0 |
BIT |
18 |
Error |
Measuring sensor failed to initialize |
OUT |
248.1 |
BIT |
19 |
Error |
Absolute encoder reference needed |
OUT |
248.2 |
BIT |
20 |
Error |
Execution error of the part program |
OUT |
248.3 |
BIT |
21 |
Warning |
Force/position out of envelope tolerance |
OUT |
248.4 |
BIT |
22 |
Error |
Envelope number to be activated doesn't exist |
OUT |
248.5 |
BIT |
23 |
Warning |
Envelope object offset too large |
OUT |
248.6 |
BIT |
24 |
Error |
Force regulator function: Position not OK |
OUT |
248.7 |
BIT |
25 |
Error |
Force regulator function: Force out of tolerance |
OUT |
249.0 |
BIT |
26 |
Error |
Negative software limit switch reached |
OUT |
249.1 |
BIT |
27 |
Error |
Maximal position limit exceeded in a positioning |
OUT |
249.2 |
BIT |
28 |
Error |
Minimal position limit exceeded in a positioning |
OUT |
249.3 |
BIT |
29 |
Error |
Speed limit exceeded in a positioning |
OUT |
249.4 |
BIT |
30 |
Error |
Acceleration/deceleration limit exceeded in a positioning |
OUT |
249.5 |
BIT |
31 |
Error |
Position limit of a positioning instruction exceeds the value of the control parameter |
OUT |
249.6 |
BIT |
32 |
Error |
Speed limit of a positioning instruction exceeds the value of the control parameter |
OUT |
249.7 |
BIT |
33 |
Error |
Acceleration/deceleration limit of a positioning instruction exceeds the value of the control parameter |
OUT |
250.0 |
BIT |
34 |
Error |
|
OUT |
250.1 |
BIT |
35 |
Error |
|
OUT |
250.2 |
BIT |
36 |
Error |
|
OUT |
250.3 |
BIT |
37 |
Error |
|
OUT |
250.4 |
BIT |
38 |
Error |
Unknown message number sending by the HMI (MecaMotion) |
OUT |
250.5 |
BIT |
39 |
Error |
Length of the message sending by the HMI (MecaMotion), not ok |
OUT |
250.6 |
BIT |
40 |
Error |
Automatic mode missing |
OUT |
250.7 |
BIT |
Table 1: Errors list
